线导鱼雷导引弹道的动力学分析

通过线导鱼雷常用导引方法—三点法、前置角法导引弹道的动力学分析 ,推导出不同方法下鱼雷旋回速率的解析表达式 ,并通过数字仿真对鱼雷线导导引弹道动力学特性进行探讨 ,明确了线导鱼雷导引弹道特性与导引方法之间的关系 .     

如何估计软件的MTBF

软件剩余初始故障个数No、平均无故障时间MTBF、故障暴露率λ和软件运行的成功率θ等是衡量软件可靠性的重要参数.其中对高可靠性软件(包括军用软件等)MTBF是最重要的.传统的MTBF计算方法有2种一是计算发生故障的平均时间间隔二是通过软件可靠性模型进行估计.前者代价较大,后者不太准确.本文从软件的失败率入手研究软件的MTBF,这是一个比较贴近实际的方法.     

火控系统最佳采样率问题的研究

先从滤波器和信号的频域特性出发给出了滤波器在频域的采样率匹配原则。第二部分从滤波器预测误差最小的原则出发导出了一组求解最佳采样时间的方程,并给出部分计算结果。第三部分提出了速度平滑处理法,解决了提高采样率引起的速度估计误差增大的矛盾。随后给出了典型航路下,综合各影响因素的模拟跟踪结果,并与“×型”指挥仪的跟踪结果作了分析对比。最后提出了针对不同空中目标的最佳采样率的建议     

异常市场的判别

给出了股票价格的Black Scholes模型中股票期望收益率μ及波动率σ2的估计,并证明了这种估计的良好性质。给出异常市场判别准则,提出第一、第二警戒值的计算公式。     

基于能量度量的星载AIS信号自适应码元同步抽取算法

基带信号码元同步抽取是目前星载AIS(Automatic Identification System)信号处理中的一个难点问题,针对过零检测和迟门早门等现有算法存在的不足,提出了基于能量度量的基带信号自适应码元同步抽取算法。将基带信号根据采样率和码速率的比值分割成相同的段的组合,之后分别计算每个段内相应样点的能量度量,最后选择使能量度量最大时的样点集作为最优同步抽取样点,该样点集具有最大信噪比。仿真结果验证了该算法误码率优于过零检测和迟门早门算法。     

单晶硅反射镜激光能量吸收系数与衬底表面质量的关联

高能激光系统中,单晶硅基底反射镜的能量吸收系数是影响系统性能的关键指标。衬底加工质量对镀膜后元件激光能量吸收系数影响显著。通过测试不同衬底粗糙度、划痕密度的单晶硅反射元件,分析衬底表面典型加工特征(粗糙度、划痕)对激光能量吸收系数的影响规律,认为粗糙度与吸收系数正相关,粗糙度均方根从0.668nm降低至0.345nm会使吸收系数降低28.0%。少量划痕对吸收系数的直接影响并不明显,吸收系数均值变化在3.1%以内。但表面划痕会诱发激光损伤,划痕密度较大时会引起后续能量吸收持续增大,辐照400s后,吸收系数较辐照100s时增大18.3%。     

Effect of organo-modified montmorillonite nanoclay on mechanical,thermal and ablation behavior of carbon fiber/phenolic resin composites

The mechanical, thermal and ablation properties of carbon phenolic (C-Ph) composites (Type-I) rein-forced with different weight percentages of organo-modified montmorillonite (o-MMT) nanoclay have been studied experimentally. Ball milling was used to disperse different weight (wt) percentages (0, 1,2,4,6 wt.％) of nanoclay into phenolic resin. Viscosity changes to resin due to nanoclay was studied. On the other hand, nanoclay added phenolic matrix composites (Type-II) were prepared to study the dispersion of nanoclay in phenolic matrix by small angle X-ray scattering and thermal stability changes to the matrix by thermogravimetric analyser (TGA). This data was used to understand the mechanical, thermal and ablation properties of Type-I composites. Inter laminar shear strength (ILSS), flexural strength and flexural modulus of Type I composites increased by about 29％, 12％and 7％respectively at 2 wt.％ addition of nanoclay beyond which these properties decreased. This was attributed to reduced fiber volume fraction (％Vf) of Type-I composites due to nanoclay addition at such high loadings. Mass ablation rate of Type-I composites was evaluated using oxy acetylene torch test at low heat flux (125 W/cm2) and high heat flux levels (500 W/cm2). Mass ablation rates have increased at both flux levels marginally up to 2 wt.％ addition of nanoclay beyond which it has increased significantly. This is in contrast to increased thermal stability observed for Type-I and Type-Ⅱ composites up to 2 wt.％addition of nanoclay. Increased ablation rates due to nanoclay addition was attributed to higher insulation effi-ciency of nanolcay, which accumulates more heat energy in limited area behind the ablation front and self-propagating ablation mechanisms triggered by thermal decomposition of organic part of nanoclay.     

A novel formulation of material nonlinear analysis in structural mechanics

This article demonstrates a novel approach for material nonlinear analysis. This analysis procedure eliminates tedious and lengthy step by step incremental and then iterative procedure adopted classically and gives direct results in the linear as well as in nonlinear range of the material behavior. Use of elastic moduli is eliminated. Instead, stress and strain functions are used as the material input in the analysis procedure. These stress and strain functions are directly derived from the stress-strain behavior of the material by the method of curve fitting. This way, the whole stress-strain diagram is utilized in the analysis which naturally exposes the response of structure when loading is in nonlinear range of the material behavior. It is found that it is an excellent computational procedure adopted so far for material nonlinear analysis which gives very accurate results, easy to adopt and simple in calculations. The method eliminates all types of linearity assumptions in basic derivations of equations and hence, eliminates all types of possibility of errors in the analysis procedure as well. As it is required to know stress distribution in the structural body by proper modelling and structural idealization, the proposed analysis approach can be regarded as stress-based analysis procedure. Basic problems such as uniaxial problem, beam bending, and torsion problems are solved. It is found that approach is very suitable for solving the problems of fracture mechanics. Energy release rate for plate with center crack and double cantilever beam specimen is also evaluated. The approach solves the fracture problem with relative ease in strength of material style calculations. For all problems, results are compared with the classical displacement-based liner theory.     

南水北调中线工程安阳段渠坡换填土的强度特性研究

为了分析南水北调中线工程安阳段渠坡的稳定性,对该渠坡换填土在不同含水率下进行了不固结不排水三轴剪切试验.研究结果表明:剪切速率对基质吸力的影响较大,而对强度的影响较小;通过比较确定了合适的剪切速率;含水率相同的试样在不同围压下的强度值在pf -qf坐标上呈良好的线性关系;得到了试样在不同含水率下的总强度指标,建立了总内...     

基于中位秩的动态可靠性增长模型

给出了一种动态可靠性增长模型。首先利用统计中的中位秩法结合试验数据确定各个增长阶段的失效率 ,这一技术可以很好地解决小子样问题 ,并且由于利用了动态建模的思想 ,因而可以客观地反映系统的实际状态。其次 ,该模型继承了传统Duane模型简单、直观、易于进行参数估计的优点 ,同时又很好地处理了传统Duane模型所不适用的分阶段、多场景试验的情形 ,因而有很广阔的工程应用前景。最后通过仿真实例验证了该模型的正确性